- Ge profile quiet 3 flashing lights manuals#
- Ge profile quiet 3 flashing lights manual#
- Ge profile quiet 3 flashing lights download#
If the above suggestions do not resolve the issue, a service call may be needed. You can save paper and ink by printing only the pages for the.
Ge profile quiet 3 flashing lights manuals#
Printing tip If printing is required, note that some manuals include multiple languages.
Ge profile quiet 3 flashing lights download#
Save time, money, and paper Download a digital copy of your owner's manual, use and care manual, installation information, and energy guides.
Ge profile quiet 3 flashing lights manual#
To turn this feature On or Off, check the owner’s manual for model specific information. OWNER’S MANUAL & INSTALLATION INSTRUCTIONS. There is one last thing you can check, though with scenario you will not see lights or sound. Some models have a Sleep or Sabbath Mode that turns off all lights and sounds on the appliance even though there is power connected. For more information, view: Dishwasher - Floor Protect / Leak Protection Feature. Press Start and allow it to run for five minutes.įor other models, please view: Dishwasher - Hums and Will Not Fill.įor models starting with GDF/GDT/PDT/CDT/DDT/ADT/ZDT, view: Dishwasher - Flood Float.Īll other models will require a service technician to diagnose and repair.įor models with an LCD display, you may have a leak protection feature that is preventing your appliance from running. For more information, view: Dishwasher - Demo Mode.ĭishwasher Making a Slight Humming Noise But Will Not Start or Run:įor models starting with the letters GDF/GDT/PDT/CDT/DDT/ADT/ZDT: Add one pint of hot tap water to the bottom of the appliance. Make sure the appliance is not in Demo Mode. For more information, view: Dishwasher - Delay Start Option. The display will show the amount of hours it will delay washing - for example, 2H - if the delayed start feature is activated. Models with a Delay Hours button will allow you to start the dishwasher now however, it won't begin washing until the set number of hours has passed. The door latch must be fully engaged for the switch to signal that the door is closed properly and is ready to run. Make sure there is nothing preventing the door from closing securely, such as trim, insulation, the countertop, etc. View a video explaining the Control Lock Feature: The way that you lock the controls does vary by model.įor model specific directions, download a copy of the Owner's Manual. Make sure the Lock feature is turned "OFF" according to the instructions in your Owner's Manual. Models with electronic controls have a child lock-out feature to prevent the dishwasher from accidentally being turned on. Checking these possible solutions often gets the appliance working again without the need for a repair. Below are a few things that could be keeping the appliance from starting. If your dishwasher is not working, but the display lights come on and button presses make sounds, it rules out the power source being the issue. Then the drain motor will NOT respond and will remain off.Dishwasher - Will Not Start or Run but Has Lights or Sound ➔If the control is not OK (still sees shorts with the keypad unplugged), Select a new wash cycle if the Start/Reset light is blinking. Close the dishwasher door until it latches, as the unit will not operate if the door is open. Reset the fuse or circuit breaker as necessary. It will respond by turning on a Drain Motor for 2 minutes.Ĭheck and/or replace the keypad if the control responds OK. Make sure the GE Quiet Power 3 is completely connected to a power outlet if it isn’t working. ➔If the control is OK (no longer sees shorts with the keypad unplugged), Make sure all other connections are made.Ĥ. Open console and disconnect the keypad ribbon connection from the control (at P1). To determine if the control or keypad is faulty, do the following test:ġ.
Indicates one or more key switch lines are stuck or shorted on either the control or the keypad. Therein it is written this simple procedure for determining whether the touchpanel or control board is the culprit:Ī rapidly blinking LED over one of the keys of the keypad (or sometimes a “dead” keypad/console) Remove the kickpanels below the door and you'll find a tech sheet in a plastic pouch (unless some sleaze bag stole it). The conundrum you face is which part to replace: the touchpanel or the control board?Įxperience says that it's almost always the touchpanel that goes bad in these cases- a keypad gets stuck closed or worn on the inside so it no longer makes contact.įortunately, there's a way to tell for sure without any guesswork! none of the lights on the panel work and the dishwasher won't runĬould take on lots of other variations but the thing they'll all have in common is that dishwasher won't run. Normal light keeps blinking but the dishwasher won't run Many times when troubleshooting a Whirlpool-built dishwasher (also sold under the Kenmore and Kitchenaid brands), you'll have a problem that looks like it could be either a bad touchpanel or the control board, but you can't really be sure.
0 kommentar(er)
